How It Installs / 12,000 BTU model

Install it yourself.
One tool: a drill.

One unit inside. One unit outside. Follow the pictures, one small step at a time.

This guide is for the 12,000 BTU mini split—not the window unit. Unsure about a step? Call us before moving on.

Start with the kit ↓
SUNLIGHT IN.COMFORT OUT.
Cooling tubes already filledTube connectors tighten by handHelp by phone
PART 01 / 06

Pick a spot

One unit goes inside. The other goes outside the same wall.

Open your boxes.

  1. Lay out the inside unit, outside unit, tubes, cables and small parts.
  2. The tubes already contain the cooling fluid. Do not cut them.
  3. Solar panels come with the Complete Kit.
BOX 1BOX 2Inside unitOutside + tubesHardware bagSolar switch+ solar cables

Keep the two units close.

  1. Pick an outside wall that can hold the inside unit.
  2. Put the outside unit on a strong, flat base on the other side.
  3. Leave a clear path for the tubes and water drain.
INSIDEOUTSIDE

Leave room around each unit.

  1. Use the measurements below. Do not squeeze the units into a tight space.
  2. Keep the front of the outside unit clear so air can blow out.
15 cm12 cm12 cmOUTDOOR · TOP VIEW30 cm behind30 cm left60 cm right200 cm front
Indoor, above: 15 cm / 6 inIndoor, each side: 12 cm / 5 inOutdoor, behind + left: 30 cm / 12 inOutdoor, right + above: 60 cm / 24 inOutdoor, in front: 200 cm / 79 in
PART 02 / 06

Hang the inside unit

Attach the wall plate, make the opening, then hang the unit.

Screw the plate to the wall.

  1. Take the metal mounting plate off the back of the unit.
  2. Hold it level. Mark and drill its five screw holes.
  3. Fit the supplied wall anchors where needed. Tighten all five screws.
Level. Then all five screws.

Make the opening for the tubes.

  1. Mark the center 6.5 inches to the right of the bottom-right screw.
  2. Make a small test hole first. Check for wires, pipes and wood framing before cutting further.
  3. For this model, the manual calls for a 2.5-inch hole, sloping down 15° toward the outside. Wear eye and ear protection.
Check the hole-saw size before drilling

Your kit includes a 3-inch hole saw, but this model’s manual specifies a 2.5-inch opening. Call us before drilling if you do not have the matching size.

6.5 in →2.5 inSIDE VIEWInsideOutside15° downhill

Gently turn the short tubes back.

  1. Leave the protective caps and wrapping on.
  2. Support the copper tubes where they leave the unit.
  3. Slowly turn them to point straight out the back. Never make a sharp bend or pinch them flat.
BACK OF INSIDE UNITBend gently. Never pinch.

Pass the parts through. Hang the unit.

  1. Feed the control cable through first, then the water-drain hose, then the copper tubes.
  2. Hook the top of the unit onto the wall plate.
  3. Press the bottom into place. Have someone help hold the unit—it weighs about 25 lb.
1 Cable2 Hose3 TubesHook the top. Push the bottom in.
PART 03 / 06

Connect the outside unit

Match the parts shown in each picture. Take one connection at a time.

Keep the drain hose at the bottom.

  1. Place the outside unit on its flat base. Unpack its tubes.
  2. Keep the water-drain hose at the bottom of the wall opening so water can run downhill.
  3. Remove the wrapping and caps from the tube ends. Support the short tubes while gently turning them down about 45°.
Caps offHose at the bottom. Always downhill.

Join the matching tubes by hand.

  1. Unroll the tubes from the outside unit toward the inside tubes.
  2. Match the small ends together (¼ inch), then the larger ends (⅜ inch).
  3. Turn each connector by hand until the two halves meet with no gap. Do not use a wrench or cut the tubes.
MATCH ¼ IN → ¼ IN · ⅜ IN → ⅜ INGap = keep turningNo gap = sealed.

Wrap the tube connections.

  1. Slide the foam covers up to the connections. Hold them with electrical tape.
  2. Wrap each connection with the wide foam tape.
  3. Cover any remaining gaps with electrical tape. No bare copper should show.
Foam up to each connectorElectrical tape → wide foam → touch up

Run the tubes down the wall.

  1. Keep about 4 feet straight below the connection, then make a gentle curve down.
  2. Use the supplied straps loosely. Do not crush the tubes or bend a sharp corner.
  3. Point the drain hose downhill, away from walkways and anything water could damage.
Gentle curves.Loose straps.Drain away from paths

Plug in the control cable.

  1. Remove the cover from the outside unit’s cable socket. Line up the plug’s grooves.
  2. Turn the plug left with gentle pressure until it clicks.
  3. Turn the black ring right to lock it.
A little more help

Left means counterclockwise. Right means clockwise. This cable lets the inside and outside units talk to each other.

1 Remove dust cap2 Turn plug left3 Turn ring right to locksnap

Plug in the power cord.

  1. Use a 120V, 60Hz outlet on a 15A or 20A breaker. If you are unsure what you have, stop and call us.
  2. An outdoor outlet needs a weatherproof cover that closes around the plugged-in cord.
  3. Do not run other power-hungry equipment on the same circuit.
120 V · 60 Hz15 or 20 A breakerWeatherproof cover

Mount the solar on/off switch.

  1. Fasten the switch box where the outside unit’s solar cables can reach.
  2. Click the cables from the unit into the BOTTOM of the box.
  3. Leave the switch OFF. The panels connect to the TOP in the next part.
A little more help

The manual calls this box a DC disconnect. Never unplug solar connectors while power is flowing.

ONTOP ← panelsBOTTOM ← unitOFF untilpanels connectPanels connected? Then turn ON.
PART 04 / 06

Connect the solar panels

Six 300W panels come with this 12,000 BTU mini-split kit.

Check the panel plan before plugging in.

  1. Call us to confirm how your full set of panels should connect. The picture shows only three panels to explain the connections.
  2. With the solar switch OFF, connect the panel cables to the TOP of the switch box.
  3. Turn the switch ON only after all connections are finished. Never unplug connectors while power is flowing.
A little more help

In a series connection, a panel’s plus (+) connects to the next panel’s minus (−). Do not copy the small example as the complete six-panel wiring plan.

−+−+−+Connection exampleTOP ↓Solar switch
PART 05 / 06

Turn it on

Use the remote first. The phone app and extra settings can wait.

Press ON. Wait about 3 minutes.

  1. Check that connections are finished, air paths are clear and the drain runs downhill.
  2. Press ON/OFF on the remote.
  3. Give it about 3 minutes to start. The bottom flap opens and air begins to flow.
A little more help

The picture’s countdown runs faster than real life. It is not a timer.

243:002:001:00Ready3-minute wait · illustration sped up

Want phone control? This part is optional.

  1. Open Solar Air Con on your phone and create an account. Use 2.4GHz Wi-Fi, turn on Bluetooth and allow Location when asked.
  2. Tap + or Add Device. With the unit on, press LIGHT on the remote 8 times within 10 seconds.
  3. When it beeps, tap Add beside your unit and enter your Wi-Fi password within 3 minutes.
Solar Air ConPairedLIGHT12345678Beep8 presses within 10 seconds

Leave extra settings for later.

  1. You can use normal heating and cooling without changing these settings.
  2. Want to limit power use? Press SE, then LEVEL on the remote.
  3. A lower setting uses less power but gives less heating or cooling.
A little more help

The display shows 78.0 for normal operation, 78.1 for a 25% compressor limit, 78.2 for 50%, or 78.3 for 75%. These numbers are settings, not room temperatures. Solar power is still used first.

SE → LEVEL78.0Normal · no limit78.125% compressor limit78.250% compressor limit78.375% compressor limitSolar is still used first.
PART 06 / 06

Keep the filters clean

A quick rinse helps air move freely.

Rinse. Let dry. Put back.

  1. Turn the unit OFF and unplug it before cleaning.
  2. Lift the front cover. Slide the filters down and out, then rinse them with tap water.
  3. Let them dry completely before putting them back. Clean monthly during heavy use, or sooner if dusty.
RINSEDRYFully dry. Then slide back in.

A real person, right here in Phoenix

Questions? Real people,
no phone tree.

Stuck on a connection or planning your panel layout? Tell us where you are in the guide. We’ll help you with the next step.

Instructions for the 12,000 BTU solar hybrid model. Download the installation manual ↓
Installing a different model? Ask us for its matching instructions.